Simple & Quick Tool Tote

Tool Tote

This post is less about the virtues of building a tote and more to do with some personal navel-gazing. Let’s deal with the tote first. I don’t think I’ve broken any new ground; my only aim was to keep it simple and strong. Attaching the base to the ends with dovetails gives a really strong foundation as this is where most of the stress and load is transmitted. All the wood grain is in the same orientation which is a bonus for long-term durability too. Dado joints on the sides lock the dovetails in and prevent the dovetails being able to lift out. The handle has a barefaced tenon giving a nice wide shoulder below the mortice to drive a nail in. I was tempted to go glueless – and I’m sure it would be plenty strong without – but a bit of PVA wood glue never hurt.

Tool Tote 3

The nails were just what happened to be around (a legacy of four generations of hoarding). The design makes use of a single length of 1″ x 7″ pine with a 2″ x 4″ cut back cut back for the handle. The base needed to be cut back by 1/2″ to allow an 1/4″ dado in the sides. Apart from that it’s minimal stock prep. The tools inside are not the “essential list”; more it was to demonstrate how much you can load into one (skip to the end of the video below to see how much can be packed in).

tool tote 2

That leads me to the navel-gazing. I’m highly likely to develop this style of video and blogging. Not so much basic tool totes but to be in the shop, let the camera run, edit the junk out and write about it. I’ve found when I’ve tried to do a series of things or the like, things get bogged down. I have a table to glue up the last drawer for and then the finish to apply. I’ve also got to get the jack plane done! Once those are out the way, I can hopefully make some tweaks.

The bogging-down is a real issue. Time is short, as I know it is for us all, and having projects stretch over months makes progress hard and less rewarding for me. The longer projects can still be done but like I said, I can have the camera running and do an update when progress is made. Anyway, if you have time, watch the video below and let me know if you think it’s something you’d like to see on other projects.

— Graham Haydon

CATEGORIES
PWM Shop Blog, Woodworking Blogs
Graham Haydon

About Graham Haydon

Graham Haydon is a Joiner based in the UK, working in the same woodworking business his great grandfather started in 1926 alongside his father, brother and a small team of craftspeople. The business makes custom architectural joinery, simple furniture and custom kitchens along with a variety of other woodworking projects. He served an apprenticeship in both Joinery and Carpentry and also gained a National Certificate in Building Studies. During his spare time he enjoys woodworking mainly with hand tools.

21 thoughts on “Simple & Quick Tool Tote

    1. Graham HaydonGraham Haydon Post author

      Agreed Jamie

      It’s a forgiving project using dado, dovetail, mortise and tenon. Turning out a half decent example would be a nice springboard into other areas of woodworking. Thanks for the comment.

      Best

      G

  1. gumpbelly

    Hi Graham

    Several noted the fast speed, but nobody mentioned how much fun they had with the same old noises sounding like power tools in real time. Loved the vid, probably didn’t learn a thing, but was still worth watching. I enjoyed watching. Versus the competition you are kickin butt, keep up the good work.

    One question, you had some soft whitewood by the looks of it, yet when shooting you used a massive old woodie, and then probably a #5, was there something different you were trying to accomplish, or just changing stuff up to see if we were dozing? Or maybe I did learn something, and didn’t know it yet 🙂

    1. Graham HaydonGraham Haydon Post author

      Hi gumpbelly

      I liked the noises too, something new to the ear! I’m glad you enjoyed watching it, that was my only real goal.

      The timber is European Redwood (think midway between SYP & EWP). I used the wooden trying plane on the shooting board as I find it comfortable and effective. I happened to grab the #4 later on as it was closer so no big plan there. Thanks for making time to watch and give your feedback.

      Best

      G

  2. mslorax

    The video was fun to watch. I have a Nicholson bench and just got my Moxon vise in. My first dovetail projects will be drawer trays. Please keep this up!

    1. Graham HaydonGraham Haydon Post author

      Hi mslorax

      Yes! Another viewer saying “fun” or “enjoyed”. It’s good to hear the motivation behind the video and write up came over. Best of luck with the DT’s, I’m sure you’ll do a great job.

      Best

      G

  3. polaski

    Did you use the same Western-style saw to size the lumber, both for the cross grain and the rip cuts?
    If so, what saw was that?
    I do understand your use of the Ryoba and Dozuki. I’m using them more and that’s why I’d like to find one Western-style hand saw “hardware store saw” for both ripping and crosscutting.

    1. Graham HaydonGraham Haydon Post author

      Hi Polaski

      I did indeed and it is a “compromise” saw. It is shown on the blade as suitable for ripping but it is better on the crosscut. It is the Irwin 880 Jack, not sure how widely available it is depending on your world location.
      There are some other options that I am yet to try, when I have I’ll let you know how I get on. Thanks for asking the question.

      Best

      G

  4. rmertens

    Graham,
    I found it fun to watch and very informative. Could you comment on why you use Japanese saws for the joinery rather than western saws?

    1. Graham HaydonGraham Haydon Post author

      Hi rmertens

      Thanks for the feedback. On the question of saws I have been using a Dozuki for a while and for me it’s been the best dovetail saw I’ve used so far. Light, nimble and fast cutting. With the Ryoba it’s similar but I’d be happy with western style carcase saw too. The nice thing about the Ryoba the rip and crosscut in one and the fast cutting. Just a question of personal preference really.

      Best

      G

  5. jeffjee

    I enjoyed the video and thought it was helpful. Thank you
    PS I was especially amused by the “jackhammer chisel”! If I could make a chisel work like that I wouldn’t avoid them so much!

    1. Graham HaydonGraham Haydon Post author

      Thanks jeffjee

      Glad you enjoyed it. Patent pending on the “jackhammer chisel”

      Best

      G

  6. Strausshaus

    That was a wonderful video– keep up this kind of thing– I am so used to power tools it is refreshing– and optimistic– to see such beautiful hand-work~!
    Also, I have yet to cut my first dovetail and now am tempted to try it. Thank you!

    1. Graham HaydonGraham Haydon Post author

      Great Strausshaus

      I’m currently trying to put another video together, hope to have it ready for the weekend. Simple projects are ideal for dovetail practice. Thanks for the encouragement.

      Best

      G

  7. buoyd

    For me, the fast-motion filming gave me a much better idea of what’s involved in the project. It was also easier to stay focused on what was going on. Although I like dovetails, watching someone cut dovetail after dovetail in real time can get boring, and it’s easy to lose track of what role a given part plays in the whole project. Your video was very informative as well as entertaining — I liked the couple of super-slow-motion plane strokes. Thanks.

    1. Graham HaydonGraham Haydon Post author

      Thanks buoyd

      I’m inclined to agree. I’ve enjoyed some of the fast motions vids out there, I tend to watch them right to the end. I was beginning to find my own content a touch boring so this was a great way to freshen it up. Hopefully I can do some more vids like this.

      Best

      G

    1. Graham HaydonGraham Haydon Post author

      Shawn, thanks!

      Ha! If only I had an ounce of DiResta’s creativity, then it really would be worth watching! More to follow.

      Best

      G

    1. Graham HaydonGraham Haydon Post author

      Hi stefanrusek

      I think I was in the shop for about three hours. However it was surprising just how much time was taken up with moving the camera about. Thanks for the question.

      Best

      G

Comments are closed.