In Chris Schwarz Blog, Chris Schwarz Woodworking Classes, Woodworking Blogs

We may receive a commission when you use our affiliate links. However, this does not impact our recommendations.


When in Canada, you do need to be careful about what you use your toothbrush for.

At woodworking schools in the United States, a lot of them use a wet toothbrush to remove wet glue squeeze-out from the inside corners of a carcase. But when teaching a tool chest class at Rosewood Studio in Perth, Ontario, I found the situation to be turned upside down.

Right before we began gluing up tool chests, I asked for an acid brush to apply the glue.

“Acid brushes,” says Ron Barter, the owner of Rosewood, with a little bit of an eyeroll. “How long are the bristles? Too long. They have to be trimmed. Where do the bristles go? Everywhere you don’t want them.”

Instead, Barter uses toothbrushes to apply the glue.

“They have to be the old-style square ones,” he says about the brushes. “It’s like a trowel for laying adhesive for a floor. A straight-bristle toothbrush does the same thing and leaves the right amount of glue.”

The other nice thing is that the toothbrushes don’t rust like the metal acid brushes. The rust can get all over the work.

So what does he do about squeeze-out? Barter waits just long enough until the stuff hardens  a bit to look rubbery.

“Then I I take a friend’s plane iron – and that’s key – and lay it down flat on the board. And I carefully slice the projecting glue beads off.”

With carcases, Ron and his students finish the inside of the case before assembly and use wax to prevent the glue squeeze-out from ruining the inside.

To see the first student in this class assemble his chest, check out the video above. Hans just finished the 12-week Craftsman program at Rosewood and is staying on at the school for additional training.

— Christopher Schwarz

P.S. The chest we’re making is from “The Anarchist’s Tool Chest,” which discusses classic chest construction and the set of tools needed to build most forms of furniture.

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.

Recent Posts
Showing 10 comments
  • Ed Burns

    Three words for Hauns. Extended open time.


    Two things – if you accidentally let the glue dry in this or any brush ( I use a “fan” shaped artist’s brush) just soak it in water.

    Also, here is a tip from luthiers who have to remove miles of glue squeeze out. Next time you are at the fast food restaurant, pick up a couple of plastic soda straws. WIth a chisel, cut the end of one at 45 degrees. Use this is a “scoop” to remove squeeze out by pushing it along the joint. The long ones are great for getting under clamps that you can’t reach. If necessary, a quick wipe with a wet paper towel takes care of the remainder of the glue. After a session, just cut off the goopy end with a new 45 and keep moving.

  • rockyferraro

    I tried this yesterday on a glue up and it worked great. It feels like the brush helps the glue go into the pores. I’m also using the tips from Robert Lang and letting the glue dry a bit before I clamp. That seems to be working well too. Thank you for all these tips and keep them coming.

  • Russell

    Hmmm… I’ve been using old toothbrushes for glue for years. I began when I had no acid brushes on hand and wanted to go ahead and do a glue-up. Since then, I hang on to my used toothbrushes. i don’t always remember to clean them after this use.

  • DeeWebb

    Chatham County Line – Let it Rock

  • larry7293

    chatham county line

  • John Walkowiak

    Do these folks a big favor, and introduce them to liquid hide glue. Their shop lives would be soooo much easier.

  • SL1800

    Chris we must know what song and artist that is in the video.

  • pmac

    Is that his normal working speed or did you give him and “Underdog Super Energy Pill”? He looks like a man on a mission.

  • ebsutton

    Hey, Chris: Who’s playing the music on this video?


Start typing and press Enter to search