In Chris Schwarz Blog, Woodworking Blogs

We may receive a commission when you use our affiliate links. However, this does not impact our recommendations.

Spade Bits

Spade bits get little respect among woodworkers. They are regarded as coarse tools that tear up the work surface – good for plumbers and rough carpentry at best.

Once you understand how to use them, however, you might change your mind about them because they are inexpensive and can do tricks that few other bits can do.

Before you rush out and buy a set from the home center, do yourself a favor and avoid the fancy ones that have a lead screw and magic coating. These cost a lot more, the coating is fairly worthless in woodworking and the lead screw puts the bit in charge of the feed rate.

Buy the simple, inexpensive ones that have a hexagonal shank (these won’t slip in the chuck). A set of 10 bits should cost about $10 to $12.

So here’s the No. 1 tip about using these bits: It’s all about how you start the cut.

Most woodworkers start with the bit at a slow rotation. This (and dull spurs) will chew up the surface of the wood right quick. Instead, place the bit’s lead tip lightly on the work and get the drill going at full speed before advancing the bit into the work. If you are using a cordless drill with a speed selector, choose high. If you have a variable-speed trigger, press it all the way.

Advance the bit slowly until the spurs engage the wood and define the circumference of the hole. Then you can dive in a little faster.

If you have never used a spade, this is where you will find out why they are so awesome. They cut quickly and refuse to clog.

The Infinitely Adjustable Bit
The other reason I use spade bits all the time is because you can adjust their diameter in infinite increments at the grinder. This trick allows you to create round mortises (in chairmaking, for example) that will fit your tenons bang on.

Let’s look at a typical problem – one I had today.

I had turned some rungs for an undercarriage and had gotten a wee bit aggressive on the lathe and turned the tenons down about .012” too small. Instead of throwing out the perfectly good spindles, I took a 1/2” spade bit to the grinder. (See the photo at the top of the entry. See that gap?)


I gently ground the long edges of the spade, taking care to grind both edges equally. (Note: You can also do this with a file.) Then I checked my work with calipers. When the bit was the same diameter as my tenon, I stopped grinding.


There are limits to what you can grind away, of course. Once the spurs are ground away, the bit will become difficult to use. That’s when I grind some bevels on the tip of the spade bit and transform it into a marking knife.

— Christopher Schwarz

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.

Recent Posts
Showing 9 comments
  • betschre

    Can you post a picture or tow of your spade bit marking knife? I have a couple of old spade bits that I might try to convert to a marking knife.

  • BobVjr

    And I thought I was the only one with a marking knife made from a spade bit. Guess I’m too late to patent that.

  • DanWyant

    A gap of 1/166.667 of an inch (1/2 of the .012 discrepancy or 1/83.333 of an inch ) is really going to keep you up at night? Has fastidiousness devolved into ob/comp behavior? Let the spindles sit over night and they may have made up a gap that small.

  • msiemsen

    I too grind spade bits to smaller diameters, one application is fitting saw bolts to their recessed holes. I have also ground them to tapers, and they can be converted into split nut drivers, or for driving slotted threaded inserts. Spade bits can also be used to enlarge undersized holes by fitting a pilot to the center lead.
    The spurs can be filed back on as well but it is really not worth the effort

  • BLZeebub

    If you want, and have the proper grinding wheels, you can also regrind outside spurs. About ten years ago, I cleaned out a junkman’s hoard at the flea market. I paid him a penny a piece. He was happy to not have to lug them back to his truck. I’m still churning through them.

    Darren is correct in warning about blowout. When building my bench I got a bit frisky and made the non-show side of my front skirt down right ugh-lee!

  • Darren Brewster

    You can also use the centre point just like the spur on your auger bits. When it pokes through drill from the other side so your hole is clean on both sides. Spade bits do like to burst through and mess up if you aren’t careful.

  • agglutination

    I second your love for the spade bit. The marking knife upcycling is awesome. You must know now that people will buy spade bits just to grind them into marking knives. Eventually we can call them Moxon knives. It’s in one of his plates I’m sure of it.


Start typing and press Enter to search

woodshop safety