In Shop Blog, Woodworking Blogs

We may receive a commission when you use our affiliate links. However, this does not impact our recommendations.

Learning woodworking isn’t just about “how to” do something. A good example of this comes from my days as an apprentice in a commercial cabinet shop. I entered the experience with a misguided, romantic notion of working beside an experienced craftsman and being tutored in the fine points of cabinetmaking. I figured I would be coached and guided as my skills developed. That type of experience may exist in old books or in woodworking schools, but the real world is quite a bit different. The old guys who taught me had mostly apprenticed in Europe and were incredibly skilled. But they didn’t fool around and they didn’t tolerate any one else fooling around. The focus was on getting work out the door. The standards for quality were very high as was the expectation that you didn’t waste a step.

plugsOne of my first tasks was to make 5,000 3/8″ oak plugs. That’s a lot of plugs, and that was just the first batch. When asked if I knew how to do it, I confidently answered yes. In the boat yard I had worked in before the cabinet shop I made plugs on a regular basis. Most of those were for repairs and the standard procedure was to grab a scrap of wood out of the trash and head to the drill press. There I set the depth of cut and randomly placed plugs. When I had however many the scrap would hold, I would head to where the work was and pop out a plug with a chisel when needed. I figured all I had to do was repeat my process 100 or 200 times.

Dec2004PLGSIt wasn’t long until I was shown the error of my ways. Lessons weren’t delivered in gentle tones, they were delivered at a high volume. I knew an important lesson was coming when I heard “LANG! WHAT THE #*($@^ DO YOU THINK YOU’RE DOING?!” Making a few acceptable plugs is one thing; making a profit on 5,000 of them is another. And so I was yelled at for not ripping the scraps into strips just a bit wider than the plug cutter. Then I was yelled at for not setting up a fence at the drill press. Then I was yelled at for not knowing that a fence at the drill press should have a step on the bottom edge so chips don’t build up. Then I was yelled at for not raising the table of the drill press so I wouldn’t need to move my arm so far with every stroke. Then I was yelled at for popping the plugs off the strip with a chisel – was I some kind of idiot who didn’t know the table saw could cut wood? The final shouting told me to lower the blade a little so that the plugs stayed attached to the strip but could easily be popped off and then I was quietly asked what made me think I would ever be a cabinetmaker.

Dec2004TrimThis was a typical day when I was an apprentice, and this is typical training in European shops where brow-beating and humiliation are considered effective motivational tools. I hated it at the time, but later on, when I was trying to make a living in my own shop, I realized how valuable this experience was. The lessons in the above paragraph aren’t specific to the task of making plugs, they apply to everything in the shop. What I really learned was that every step of any process is an opportunity to do things more efficiently, to make the work less tedious and the end product better. It’s about working smarter instead of working harder and eventually I learned to look for the easiest way to do things. Woodworking is a lot of fun when you aren’t doing things the hard way. Making it easy and fun is a worthy goal, whether you’re making one of something as a hobby or a boatload of things to pay the bills.

–Robert W. Lang

Frank Klausz reminds me of the guys I worked with back in the day. He apprenticed in his native Hungary and ran his own shop for years. In his new video “Joinery Master Class” he’ll teach you what you need to know, without yelling at you.

Product Recommendations

Here are some supplies and tools we find essential in our everyday work around the shop. We may receive a commission from sales referred by our links; however, we have carefully selected these products for their usefulness and quality.

Recommended Posts
Showing 9 comments
  • JMAW Works

    Thanks Bob for sharing this story, I think it touches on 2 separate points. One that hobbiests can learn a lot about efficiencies from those with dinner on the line. The second, more philosophical goes to how to treat new folks, the type of work involved is really irrelevant. In my beginning time of corporate office work it was the same style of “apprenticeship”, beat new guys down. Later, I moved to a “touchy feely” division (in the words of my first divison) I really grew professionally in that environment, where people can suggest ideas or ask for help without being berated for it. Understanding the culture of a group is now one of the primary things I look for in choosing where I work, and a guiding principle in how I treat newbies.

  • Bryan Robinson

    Great post, thanks.

  • redguy

    In my undergrad days at University, I worked in Plant Operations. Around my class schedule, I worked in 3 departments during my tenure: Cement Crew, Paint Shop and Carpentry. Each of these provided an environment not unlike the apprenticeship that Bob describes in his article. It was hard work requiring some “toughness of soul” to perform day-in and day-out under “tough souls” who instructed and supervised me. Yes, it could be harsh but I learned, and not just about the task at hand but about myself, about life and about people. It was, in actuality a rich experience but maybe not for everyone. I was taught first quality, then efficiency and economy – in short mastery (not a destination but an ongoing process). I learned to own my mistakes. As a young man, I also learned that being a man includes humility under authority as well as integrity – it was a sort of coming of age for me. How golden were those moments when, over the course of work and time, I knew I had finally measured up in the eyes of those “tough souls” whose tutelage I was entrusted to-perhaps the real gold in my education!

  • Ron 1

    Yes…the first couple of apprenticeship years are not a fond memory.

  • ThorsWagon

    “This was a typical day when I was an apprentice, and this is typical training in European shops where brow-beating and humiliation are considered effective motivational tools” Not ok then. Not ok now. In Europe or The States or any where. Its kind of sad that you view this as a valuable learning experience when the only real value there is that you showed intestinal fortitude by taking the information and not knocking your abuser on his backside. Unfortunately far to many at that age do not learn or grow from this but instead develop bad attitudes or fall by the wayside. I have felt the rage that comes from being treated this way and can tell you nothing is learned except hatred. So, the lesson here for me is that it is people like yourself that are perpetuating this type of at work abuse and your attitude about it is DEAD WRONG. There is no greater joy in life than being able to show someone, a co-worker, new guy, old guy, any one how to get something done whilst in the thick of it and see them grasp the info and use it , without being abusive, without negativity. Then there is only gratitude and success. You need to rethink your attitude about the past and realize that just because you survived that , it doesn’t make it ok.

  • keithm

    Never worked for me, “…brow-beating and humiliation are considered effective motivational tools.” Just glad I was never in service’s “Basic Training.”

  • deric

    This reminds me of my early years in carpentry. I learned a bunch and never made the same mistake twice but you really had to have thick skin to survive. Funny thing was after a few years one day I knocked one of the guys on his backside after he went off on me for nothing, after that they treated me as one of the guys. The lessons after that were delivered in a very pleasant manner.


Start typing and press Enter to search