Comments on: New SketchUp Drawing of a Roubo Workbench

By: ocd

ocd — Tue, 02 Jun 2009 17:19:23 +0000

test

By: David Ragan

David Ragan — Tue, 02 Jun 2009 17:06:30 +0000

test

By: Caleb Dunn

Caleb Dunn — Tue, 02 Jun 2009 15:00:22 +0000

I’ll try to explain my cross-cut situation.
Last week I made a bow saw, and had to rip three narrow strips that were about 1.5"wide and 16" long to make the frame. I simply put the 6" wide piece of wood in my face vise on the edge of my bench and ripped the narrow pieces in one long cut. If my future Rubo has a crochet on it I would not be able to do that. So, I was considering building a Rubo where the leg vise was on the end of the bench-top so that I could do similar cuts.
Would you consider this a wise modification?
Thanks, Caleb

By: Cosmo

Cosmo — Tue, 02 Jun 2009 14:39:56 +0000

Thanks for the clarification everyone.

So, I can see the benefits of this configuration: wheel closer to the front of the bench, no dog hole in the leg. How about the dog holes being further away from the front apron? How much of a difference in HOLDING and FEEL do you think it makes? I imagine not much. But, I would be interested to get your opinion.

By: Christopher Schwarz

Christopher Schwarz — Tue, 02 Jun 2009 14:31:04 +0000

Caleb,

I’m not following you. Do you actually mean for doing long crosscuts? I can’t envision how the bench would get in the way of a long rip.

For crosscutting long pieces, it depends on the width of material. For narrow pieces, I do it on the bench with two bench hooks. For wide pieces, I do it on sawbenches with a crosscut handsaw.

If I’m missing something here, let me know.

Chris

By: Caleb Dunn

Caleb Dunn — Tue, 02 Jun 2009 13:37:09 +0000

I have been dreaming about building a Rubo since I found this web-site. One question I have is weather or not it would be a good idea to have the edge of the leg vise meet the edge of the bench. I find that in my current setup I use my vise to hold pieces for ripping and this allows me to cut without the saw hitting the bench (I don’t have any power tools). Or, do you have a better suggestion of holding a piece firmly for ripping long cuts?
Thanks.

By: Jameel Abraham

Jameel Abraham — Tue, 02 Jun 2009 01:01:57 +0000

Nice drawing Chris N.

Cosmo, Josh, Chris and Chris are right about mounting a lefty at the right end of a bench. There’s also a PDF on the BC website detailing Chris’ (Schwarz) installation.

By: Christopher Schwarz

Christopher Schwarz — Mon, 01 Jun 2009 19:21:53 +0000

Chris,

My bars are 15" long – Jameel cut them down for me.

Chris

By: Chris Norman

Chris Norman — Mon, 01 Jun 2009 18:42:33 +0000

Thanks for posting this Chris.

I put the drawing out in the Sketchup 3D Warehouse so I could get feedback especially on the changes from your design.

Chris, one question I had: How long are the slider bars on your benchcrafted vise? I ended up needing to extend my benchtop about 1.5in longer than the plan in your book to accommodate the slider and screw length to avoid the Right Front leg of the bench. In the pictures I have seen of your bench, it looks like your slides may be a little shorter than the standard bars.

Cosmo, I am using a lefthand Benchcrafted vise in the right hand position. I wanted to avoid having a benchdog hole in the middle of my leg like Jameel did, so I pushed the vise behind the leg and used a left hand model to bring the wheel closer to the front of the bench

By: Josh

Josh — Mon, 01 Jun 2009 17:35:50 +0000

Ooh, even a benchcrafted vise! This Saturday is set aside to install mine. Jameel sold me on one in Cincy.

Cosmo, I believe you can mount left or right handed version either way. According to info on BC’s website, mounting the left hand version in a right hand configuration moves the wheel closer to the front of the bench. I believe that is what Chris did so I am sure he can comment.

Josh