Plane Facts

Plane one big and one smallNow that I’m officially on board I figure I’ll get the obligatory plane post out of the way early. Sure, I did my touchy-feely First Day post last week. And while I was in the PopWood offices (I’m back home in Penn. now until we make the final move) I got a chance to play around with Jet’s new 719200 lathe (read a little about it here) in order to review it for the October issue of the magazine. Now some would say those are “official” blog posts but I understand you are not “really” an editor until you’ve posted about planes.

Plane flatness check

For quite some time I’ve heard about lapping the sole of a plane in order to get it absolutely perfectly flat. Hogwash. Sure, flattening a plane can make life easier but it just isn’t a “necessity.” Those who think a plane is useless without being perfectly flat just don’t understand what a plane is or how it works, and they certainly don’t understand the tolerances of the medium in which we work. With all that said, I’ve never flattened a plane.

I’m a pretty meticulous woodworker but I only work to the nearest 1/32″. If my plane measures within that tolerance of being flat, I’m OK with it. I’ve always thought flattening planes is a waste of good woodworking time. If a plane is that far out of flat, throw it away and get another. If it’s an old plane, it just means someone abused it. If it’s new, it’s a defect.

Plane of choiceThe biggest problem I have with flattening planes is, my plane of choice is just too big to flatten. From what I’ve read, people spend days flattening a simple smooth plane. How long is it going to take for me to lap this to perfection?

Whether your plane is hand or power, you really only need to know a few things. For a handplane, three points need to be in the same plane: the toe, the area right behind the mouth and somewhere toward the back of the plane. Honestly, you really can get away with two of those. The only one that has to remain is the spot right behind the mouth. It means you may have to learn how to apply pressure differently as you use the plane but it will still work. Sharp is far more important than flat. I don’t care what method you use to sharpen. Just pick the one that makes the most sense to you. Whether it’s a really old method of sharpening, mine or someone else’s, just sharpen.

For my plane of choice, I merely need to make sure my knives are parallel to my outfeed table and that my outfeed table is in line with the apex of the arc of the cutterhead. Once I achieve that, everything else is fairly inconsequential. Again, sharp is far more important than flat.

I may have oversimplified things a bit but it is my first “official” editorial post. One of the biggest problems I’ve seen with woodworkers over the years is, they worry the minutiae to death and don’t get to do what’s important: woodworking. Get into your shop, sharpen (because that’s far more important than flat) and set up your tools as quickly as possible and build something. If you do it often enough you’ll get better or you could spend all your time worrying about your plane being “a couple of thou” out of flat.

— Chuck Bender

p.s. If you just can’t bear to replace an old handplane and would prefer to give it new life, check out Christopher Schwarz’s DVD “Super-Tune a Handplane: How to Turn a Flea-market Find into a Fast, Accurate and Smooth-cutting Tool.

34 thoughts on “Plane Facts

  1. Eric R

    I like what you are saying Chuck.
    Don’t let those who disagree with you influence your stance.
    I’ve been a fan of your work for a long time.
    I think you know what works and what doesn’t.

  2. 7-Thumbs

    I love it and I’m with you. But be careful, I understand that Christopher Schwarz has super sharpened his No. 8, flattened the sole to 0.00000001 in and he’s gunning for you.

  3. Bill Lattanzio

    A couple of things I’ve found out: Sharp trumps flat everyday of the week; there is no such thing as a perfectly flat hand plane; the board will tell you how flat it is, not the plane; sole flatness has nothing to do with creating a good glue edge which is the real job of a jointer; if your stock is so rough that you need to spend hours flattening it, find a place that has better stock.

  4. Chuck BenderChuck Bender Post author

    ‘I know you’re out there… I know that you’re afraid. You’re afraid of change…I don’t know the future…I didn’t come here to tell you how this is going to end, I came here to tell you how this is going to begin. Now, I’m going to stop replying to this post and I’m going to show these people what you don’t want them to see. I’m going to show them a woodworking world without rules and controls, without borders or boundaries. A woodworking world…where anything is possible.’

    1. Megan FitzpatrickMegan Fitzpatrick

      And we will continue to show a variety of methods and techniques, and offer informed opinions from perhaps differing viewpoints and experience. Some folks are firmly in the flat plane camp; I am among them.

  5. David Charlesworth

    I am real sorry for Chuck.

    His tennons don’t fit. Very few glues fill gaps of 1/32 inch.

    He can’t plane a flat surface because of the hollow in his plane. His doors and drawers don’t fit.

    I could, but will not, go on for hours about his mistaken and missleading attitude to accuracy and tolerances.

    Please do not continue with this ludicrous heresy. ( I’d much prefer a rude word beginning with B).

    best wishes
    David Charlesworth

  6. David Cockey

    Looks like Chuck’s advice on what is important for a “plane” is based on a powered “plane” with rotating knives/irons for which the depth of cut is adjusted by raising or lowering the portion of the sole ahead of the knives, aka in-feed table, relative to the knives and portion of the sole behind the knives, aka out-feed table; what is frequently called a powered joiner. It looks like good advice for that type of “plane”.

    Not such good advice for a “plane” with a non-rotating iron/knife for which the depth of cut is adjusted by raising or lowering the iron/knife relative to the entire sole, ie both the in-feed and out-feed tables; what is commonly called a hand plane. If the sole is worn excessively just ahead of the mouth compared to behind the mouth the plane won’t behave properly.

    Soles of hand planes do not need to be “perfectly” flat, and Japanese hand planes demonstrate that. But they need to be close enough to flat in the right places, and the right places need to be close enough to planar with each other. How close is “close enough” depends on how the plane needs to perform, the wood being planed, etc.

  7. David Cockey

    Chuck, I don’t believe that you “only work to the nearest 1/32″.” I’ve watched you cut dovetails and your saw cuts are considerably closer than “the nearest 1/32″.” And I suspect if you are jointing the edges of boards for a glue joint you won’t tolerate a 1/32″ gap at the ends of the joint. Perhaps what you mean is that you “dimension” to the nearest 1/32″ but you fit joints to much finer accuracy.

  8. David Cockey

    I have a very nice old #3 size plane which just wouldn’t work right when I acquired it. With the iron adjusted for a reasonable shaving in the middle of a board, it would grab and try to take too wide when starting with just the toe on the board. If I retracted the iron so it didn’t grab when starting, it was too far retracted to cut the wood with the full length of the plane on the board, Turns out the sole was worn concave, particularly in front of the mouth. I didn’t measure how much it was worn but it was certainly less than 1/32″; probably around 10-thousands or so. Less than hour or so with a granite plate and some 80 grit sandpaper and the sole is flat enough for the plane to work very nicely. I don’t know exactly how flat the sole is though.

    1. David Cockey

      Should have been “too thick a shaving” not “too wide” in the second sentence.

  9. jerryolson19

    At last a new voice of reason in the wilderness. Now please don’t start selling off all of your “excess” tools.
    Don’t get me wrong the Schwarz is one of my favorites. I just like all of my tools….. and books.

  10. Albert Rasch

    Well Mr Chuck,
    At least you’re not scared to stir the pot a bit.

    I disagree, but only because I’m older, obstinate, and in all honesty a contrarian…

    Best regards,
    Albert A Rasch
    Merrily dodging 107s at FOB Shank Afghanistan

  11. Kees

    Back of the mouth? Are you sure you don’t mean the front?

    When my wooden smoothing plane refuses to take thin shavings it usually means the sole isn’t flat anymore (“flat” as in the toe, the front of the mouth and the heel being coplanar). Usually a bulge has formed at the back of the mouth, thus raising the front of the mouth off the wood. That makes adjusting the iron to a thin shaving very difficult.

  12. MikeyD

    I’ll admit it. I’ve never understood the point of feeler gauges in a woodshop. I see power tool reviews that judge the flatness of a tablesaw to the thousandths of an inch. Or jointer fences.
    We’re working in a medium that moves more than that if it happens to be raining that day.
    Am I missing something here?

  13. Mark

    Challenging closely held religious dogma within your first month? This could prove interesting.

    Good luck and keep up the good fight.

Comments are closed.